GM Tailpipe Kits
GM Tailpipe Kits
888-465-7260
This page is devoted to Tailpipe Kits only. Each kit comes with all necessary hanging hardware; including clamps and hangers. All Clamps are Zinc Coated and all nuts, bolts & washers are stainless steel. All of these kits are designed to be used with Offset outlet Mufflers unless noted otherwise. The GM G-Body Tailpipe Kits will need muffler mounting to be at a 10 degree angle relative to the center of the vehicle. We have 10 Degree Adapters which can be mounted in front of the muffler to give the proper angle.
For photographs and undercar car photos, see the appropriate sections under Header Applications.
| GM A-BODY 3½", 3" & 2½" | ||||
| 3½" | '68-72 AND '66-67 Chevelle/SS | Turn Down Tailpipes | GMA35100T | $335 |
| '64-72 | Straight Tailpipes 2-Piece Tails | GMA35111T | $379 | |
| * Note: The Straight Tailpipes are 2-piece. You will receive the TurnDown Tails, cut off the Turn Down and slip-on a Straight Extension provided.- OR, after cutting off the Turn Down and slipping on the Straight Extension, you can trim it to length and weld on the Turn Down. | ||||
| '64-67 & '73-77 Buick, Olds Pontiac GTO, '68-72 Grand Prix & '64-65 & '73-77 Chevelle; '64-77 El Camino | ||||
| Turn Down Tailpipes 2-Piece Tailpipe | GMA35111T |
$379 |
||
| Straight Tailpipes 2-Piece Tailpipe | GMA35111T | $379 | ||
| * Note: Tailpipe for the 1968 - 72 vehicles will fit '64-67, but they will be short. All 1973 - 77 3.5" tails will need to be "dinged" somewhat between the upper control arm and Coil Spring - just like we have to do with headers sometimes. | ||||
| See Note Above | ||||
| 3" | '68-72 AND '66-67 Chevelle/SS 1-Piece Tailpipes | |||
|
w/Turn Down Tailpipes |
GMA30100T | only $257 | ||
|
w/Straight Tailpipes |
GMA30110T | only $257 | ||
| '64-67 and '73-77 Except '66-67 Chevelle 2-Piece Tailpipes | ||||
| Turn Down Tailpipes | GMA30101T | only $299 | ||
| Straight Tailpipes | GMA30111T | only $277 | ||
| 2½" | '68-72 AND '66-67 Chevelle/SS 1-Piece Tailpipes | |||
|
w/Turn Down Tailpipes |
GMA25100T | only $215 | ||
|
w/Straight Tailpipes |
GMA25110T | only $215 | ||
| '64-67 and '73-77 Except '66-67 Chevelle 2-Piece Tailpipes | ||||
| Turn Down Tailpipes | GMA25101T | only $257 | ||
| Straight Tailpipes | GMA25111T | only $234 | ||
| STAINLESS STEEL Clamp Upgrade Kit | ||||
| Above 2½" and 3" kits utilize 4 clamps. You can substitute | ||||
| U-Bolt and/or Band Clamps | ||||
| Mix & Match types of clamps if you wish. | 2½" & 3" SS U-Bolt | $4.75 ea | ||
| 2½" & 3" SS Band Clamps | $7.75 ea | |||
| 3½" SS Band Clamps | $9.75 ea | |||
| GM F-BODY 3½", 3" & 2½" | |||
| 1st Gen. '67-69 Camaro, Firebird, Trans Am, '68-74 Nova, Apollo | |||
| 2nd Gen. '70-81 Camaro, Firebird, Trans Am | |||
| 3½" | 1st Gen. | GMF35100T | $339 |
| 2nd Gen. | GMF35110T | $339 | |
| 3" | 1st Gen. | GMF30100T | $272 |
| 2nd Gen. | GMF30110T | $272 | |
| 2½" | 1st Gen. | GMF25100T | $248 |
| 2nd Gen. | GMF25110T | $248 | |
| STAINLESS STEEL Clamp Upgrade Kit | ||
| Above 2½" and 3" 1st Gen Kits utilize 6 Clamps Above 2½" and 3" 2nd Gen Kits utilize 4 Clamps You can substitute | ||
| U-Bolt and/or Band Clamps | ||
|
(You can mix and match types)
|
SS U-Bolt | $4.75 ea |
| 2½" & 3" SS Band Clamps | $7.75 ea | |
| 3.5" SS Band Clamps | $9.75 ea | |
| GM G-BODY 3" & 2.5" (Header & Cat-Back) | |||
| 3" | Behind the Wheel Tails | (GMG30200T) | only $240 |
| Monte SS Tails | (GMG30210T) | only $257 | |
| 2½" | Behind the Wheel Tails | (GMG25200T) | only $200 |
| Monte SS Tails | (GMG25210T) | only $215 | |
| STAINLESS STEEL Clamp Upgrade Kit | ||
| Above Tailpipe Kits utilize 2 clamps. You can substitute | ||
| U-Bolt and/or Band Clamps | ||
| (You can mix and match types) | SS U-Bolt | $4.75 ea |
| 2½" & 3" SS Band Clamps | $7.75 ea | |
| 3½" SS Band Clamps | $9.75 ea | |
NOTE: Check out the photos on the G-Body page as you will need to use Offset Out mufflers placed at an angle. Our 10 Degree adapters can help you get the correct angle IF you are using Offset Inlet mufflers and place them over close to the driveshaft as in the photos. See Extension/Misc Pieces Page for further info.
| 10 Degree Adapters | ||
| 3" | ADP30013 | $ 27 ea |
| 2.5" | ADP25013 | $ 27 ea |
(Please give vehicle, engine and year & any other pertinent info so we can answer your question and send the correct information)
"All performance
exhaust products for pollution controlled vehicles are intended for off-road or
drag strip use only"
Copyright © 2002-2008, Torque Tech & Co., Inc. All rights reserved.
This page last
updated:
06/09/2008