Super Systems -- Systems of a certain size with the Tailpipes being the next size smaller. For example, a 3" system with 2.5" Tailpipes or a 3.5" system with 3" Tailpipes.
Kits for the following vehicles:
- Chevelle ---------------------- 1966-72
- Monte Carlo ---------------- 1968-72
- Malibu ------------------------ 1968-72
- Buick GS/Skylark -------- 1968-72
- Olds 442/Cutlass --------- 1968-72
- Pontiac GTO/LeMans --- 1968-72
- Pontiac Grand Prix ------ 1968-72
Systems come with:
- Traditional Balance Tube/H-Pipe
Both Kits come with everything needed for installation; gaskets, clamps, gaskets, etc. - all except mufflers which are purchased separately. Click here for mufflers
Kits with Balance Tube / H-Pipe:
These Kits come with Balance Tube/H-Pipe, Collector Reducers & Gaskets (3.5"x2.5", 3.5"x3", 3"x3" or 3"x 2.5"), Headpipes, Tailpipes and all clamps and hangers.
(NOTE: If you need "Slip-On" Collectors, they can be substituted; however sometimes, depending on header this can cause you to come up short lengthwise. Please call to discuss. ---------- If you need Ball & Socket Reducers, Call.) Collector Reducers
Kits with X-Pipe:
These Kits come with the X-Pipe assembly instead of the Balance Tube / H-Pipe. If you have 3.5" collectors, then you will have 3.5" tubing back to the X-Junction, then 3" tubing out the back of the Junction to the mufflers and tails. However, IF you are ordering a 2.5" System, then it will be the same as described above, EXCEPT just before the muffler the system will reduce for 2.5" Muffs (or you can reduce after the Muffs IF you have room.
(NOTE: If you have headers which require a 'Slip-On' type hookup; then you have to consider two alternatives:
- Expand Forward Extension of X-Pipe Assembly to slip over header
- Or, use Ball & Socket Setup
The following Kits utilize the Balance Tube/H-Pipe
These Kits come with Balance Tube/H-Pipe, Collector Reducers & Gaskets (3.5"x2.5", 3.5"x3", 3"x3" or 3"x 2.5"), Headpipes, Tailpipes and all clamps and hangers.
(NOTE: If you need "Slip-On" Collectors, they can be substituted; however sometimes,depending on header this cause you to come up short lengthwise. Please call to discuss. ---------- If you need Ball & Socket Reducers, Call.)
All Tailpipes exit under the rear bumper. Straight Tails will be short as we are anticipating you will use Tips.
Systems for the following vehicles: (Utilize 2-Piece Tails)
* 2-Piece Tails utilizing Turn Down Ends will typically come with 40 Degree Turn Downs unless you specify one of the following: 10, 19, or 45 degree. Exception: 2.5" 2-Piece Tails normally come with 45 Degree Turn Downs
- Chevelle ----------------------- 1964 - 65 & 1973 - 77
- Malibu ------------------------- 1964 - 65 & 1973 - 77
- Monte Carlo ---------------- 1964 - 65 & 1973 - 77
- El Camino ------------------- all 1964 - 77
- Buick GS/Skylark -------- 1964 - 67 & 1973 - 77
- Olds 442/Cutlass --------- 1964 - 67 & 1973 - 77
- Pontiac GTO/LeMans --- 1964 - 67 & 1973 - 77
for Systems utilizing X-Pipes
*Systems with Straight Tailpipes are designed to be short of the bumper since tips will be used.
For more detail about the X-Pipe Layout
Or
To Purchase just the X-Pipe Kit (No Tailpipes)
GM A-Body
"Super Systems"
to fit Header Applications
Systems for the following vehicles: (Utilize 2-Piece Tails)
- Chevelle ----------------------- 1964 - 65 & 1973 - 77
- Malibu ------------------------- 1964 - 65 & 1973 - 77
- Monte Carlo ---------------- 1964 - 65 & 1973 - 77
- El Camino ------------------- all 1964 - 77
- Buick GS/Skylark -------- 1964 - 67 & 1973 - 77
- Olds 442/Cutlass --------- 1964 - 67 & 1973 - 77
- Pontiac GTO/LeMans --- 1964 - 67 & 1973 - 77
Click here for Listing & Pricing
Going Fast is Our Business!
Performance, Fit, & Service -- All part of our products!
Order Mufflers Separate:
Stainless Clamp Upgrade
All the above kits utilize 8 Clamps for those
who wish to do some Clamp Upgrades to Stainless.
Balance Tube Upgrade
Typically each of the above kits comes with a Balance Tube. It's basically a straight piece of tubing. However, some might prefer to have a 2-Piece whick can be pulled apart if necessary, then we have Kit B. Click here for more info.
Make-a-DownPipe Kits - MaD Kits
For applications not listed above, we have what we call
Make-a-DownPipe Kits. These kits enable one to make
your own DownPipe utilizing mandrel bent elbows.
Contact Info:
Phone: (229) 242-0691
Office Hours:
Monday - Friday
9 am to 5 pm
Eastern Time
All tubing is:
- 16 ga US grade Aluminized Steel
- 'aluminized' throughout the metal, not just a surface coating
- Long Term Value with US made
Want more details on the dimensions of the X?
Need Mufflers to fit our systems? Click Here
Need Mufflers to fit our systems? Click Here